C7 ACERT™ Hazardous Location Engine

Product Description

Cat C7 ACERT hazardous location engines are the ideal solution for specialized and demanding operations in the oilfield. Engines are hazardous-location certified from the factory to minimize installation design, time, and cost. Decades of field operation and intense research and development allow Cat C7 ACERT hazardous location engines to deliver excellent performance with low operating costs and emissions. Hazardous location engines are certified to operate in potentially explosive environments. Applications powered by C7 ACERT engines include pump skids, acidizing units, cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C7 ACERT hazardous location engines, with ratings 153-172 bkW (205-230 bhp) @ 2200 rpm meet IMO Tier II, U.S. EPA Marine Tier 3, EPA Non-road Tier 3 equivalent and EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.

General Specifications

Maximum Rating
275BHP
Displacement
442in³
Minimum Rating
205BHP
Governor and Protection
Electronic ADEM™ A4
Aspiration
Turbocharged-Aftercooled
Flywheel and Flywheel Housing
SAE 1,2, or 3
Flywheel Teeth
156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
Rotation from Flywheel End
Counterclockwise
Stroke
5in
Bore
4.3in

Emissions

Emissions
EPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II

Dimensions

Length
41.5in
Width
29.8in
Height
40.6in
Weight
1386lb

Capacity for Liquids

Lube Oil System - Refill
36gal (US)
Cooling System
78.2gal (US)

Standard Equipment

  • Air Inlet System
    • Turbocharger, separate circuit (SCAC) or remote (REMAC) aftercooler
    • Single, right-side, center-mounted turbo with water-cooled turbine housing
    • Air inlet, RH side, rear facing, 101.6 mm (4 in.) connection type
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Fuel cooled ECU
    • Power compensation for fuel temperature
    • Programmable low and high idle
    • Electronic diagnostics and fault logging
    • Programmable monitoring system (engine speed, temperature, pressure)
    • J1939 broadcast (diagnostic and engine status)
    • Certified electrical control system
    • Derated engine: automatic ambient temperature compensation
  • Cooling System
    • Thermostats and housing, front-facing outlet — 51 mm (2.01 in) connection
    • Jacket water pump — belt-driven, centrifugal
    • Water pump — inlet RH front vertical inlet (pointing down) — 63 mm (2.48 in)
  • Exhaust System
    • Single, right-side, center-mounted turbo with water-cooled turbine housing
    • Exhaust manifold — water-cooled
    • Front turbo exhaust
  • Flywheels And Flywheel Housing
    • Mandatory selection of: SAE No. 1, SAE No. 2, or SAE No. 3 flywheel and housing SAE standard rotation
  • Fuel System
    • HEUI fuel system
    • Fuel filter — secondary, LH front (2-micron high performance)
    • Fuel transfer pump — left front
    • Fuel priming pump — left front
  • Lube System
    • Crankcase breather — top rear
    • Crankcase fumes disposal — RH
    • Oil cooler — RH
    • Oil filter — RH
    • Oil pan — front sump, 31 L (33 qt) oil change capacity
    • Oil filler — front top valve cover
    • Oil level gauge — LH rear
    • Engine oil pump — gear-driven
    • Oil valve sampling, RH
  • Power Take-offs
    • Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
  • General
    • Vibration damper
    • Lifting eyes
    • Literature
    • No paint
  • Mandatory Options
    • Flywheel housing and flywheel
    • Primary filter/water separator
    • Turbo orientation

Optional Equipment

  • Air Compressors
    • Air compressor governor
  • Air Inlet System
    • Precleaner
    • Air inlet elbow
    • Charging System
    • Cooling System
  • Emissions Certifications
    • IMO certification
  • Flywheels And Flywheel Housing
    • Crankshaft seal
  • Instrumentation
    • Gauges and instrument panels
  • Lube System
    • Oil pans
    • Drain and cover
    • Remote oil filters
    • Lubricating oils
  • Mounting System
    • Structural steel base
    • Engine support — front and rear
  • Power Take-offs
    • Rear enclosed clutches
    • Hydraulic pump drives
    • Crankshaft pulleys
  • General
    • Tool set